Menu
play vidio

new special over water bike

new special over water bike

YANTAI NEEDA BOATS Tech-DEVELOPMENT CO.,LTD.

25 views
Uploaded on 1 week ago
1.contrnts:
Steering Grip , Car seat , Shaft drive system Safety Pedal , S-hook, Inflatable float,Adjusting Lever, Aluminum frame structures, Plum nut
2. Product accessory drawing
3. Installation steps
3.1 " Prepare the buoy for inflationThe inflatable pontoon is unfolded and pre-inflated with a foot pump. The Pontoon does not need to be inflated to be too full. The Air Chamber can be formed and placed in reserve.
Float inflating step:3.2 Installation and debugging of aluminum alloy frame
3.2.1 Remove the TAB stop ring and place the spare using the multi-purpose tool in our tool bag, as shown in figure 1.3.2.2 Use a separate wrench in the tool bag to install the pedal crank.
3.2.3 Use the multi-function tool to fix the steering grip, the fixed position is horizontally centered symmetrically, and the Longitudinal position is shown in figure 2.
3.2.4 Use the multi-functional tool to secure the bike seat. There are 3 fixing holes in the seat mounting tube, which can be fixed according to the customer's comfort. see figuer 3. Figure 1 Figure 2 Figure 3 3.3 Integral installation of product3.3.1 install a support cross bar on the inflatable float, with the cross bar divided by the middle hole. See figure 4. Remove the nut and insert the screw from the bottom to the top at the position in figure 4.The the front and rear cross bar s type hooks are hung on the float ring, see figure 5.
3.3.2 place the fr3.3.2 place the frame on the already installed support crossbar. Please take off the rudder when installing, insert it directly into the reserved hole of the support crossbar when the position is suitable, and lock the retaining ring in the clamping slot. see figure 6.
3.3.3 insert the aluminum alloy frame retaining bolts and tighten them with a single hand nut at the bottom, as shown in figure 7. 3.3.4 swing the shaft drive system from the preset position to the working position and fix it with limit bolts for easy stopping, see figure 8.
3.3.5 use the foot pump to inflate the float again until the float is straight and ready for launching. Figure 4 Figure 5 Figure 6 Figure 7 Figure 84. Points to note4.1 The shaft drive system is a precision mating system. Please pay attention to the depth of the water line (about 50 cm) to avoid damage to the propeller. 4.2 If there is a small amount of lubricating oil in the shaft transmission system, it is a normal phenomenon. 4.3 inflatable floats are air-tight products, to avoid sand and gravel rubble, shells and other sharp objects scratch. If there is any damage, please use the repair kit to repair in time to avoid complete damaget2. Product accessory drawing 3. Installation steps3.1 Prepare the bu3.1 Prepare the buoy for inflationThe inflatable pontoon is unfolded and pre-inflated with a foot pump. The Pontoon does not need to be inflated
Chamber can be formed and placed in reserve.Float inflating step:3.2 Installation and debugging of aluminum alloy frame3.2.1 Remove the TAB stop ring and place the spare using the multi-purpose tool in our tool bag, as shown in figure 1.3.2.2 Use a separate wrench in the tool bag to install the pedal crank.3.2.3 Use the multi-function tool to fix the steering grip, the fixed position is horizontally centered symmetrically, and the Longitudinal position is shown in figure 2.3.2.4 Use the multi-functional tool to secure the bike seat. There are 3 fixing holes in the seat mounting tube, which can be fixed according to the customer's comfort. see figuer 3. Figure 1 Figure 2 Figure 3 3.3 Integral installation of product3.3.1 install a support cross bar on the inflatable float, with the cross bar divided by the middle hole. See figure 4. Remove the nut and insert the screw from the bottom to the top at position in figure 4.The the front and rear cross bar s type hooks are hung on the float ring, see figure 5. 3.3.2 place the fr3.3.2 place the frame on the already installed support crossbar. Please take off the rudder when installing, insert it directly into the reserved hole of the support crossbar when the position is suitable, and lock the retaining ring in the clamping slot. see figure 6. 3.3.3 insert the aluminum alloy frame retaining bolts and tighten them with a single hand nut at the bottom, as shown in figure 7. 3.3.4 swing the shaft drive system from the preset position to the working position and fix it with limit bolts for easy stopping, see figure 8. 3.3.5 use the foot pump to inflate the float again until the float is straight and ready for launching. Figure 4 Figure 5 Figure 6 Figure 7 Figure 84. Points to note4.1 The shaft drive system is a precision mating system. Please pay attention to the depth of the water line (about 50 cm) to avoid damage to the propeller. 4.2 If there is a small amount of lubricating oil in the shaft transmission system, it is a normal phenomenon. 4.3 inflatable floats are air-tight products, to avoid sand and gravel rubble, shells and other sharp objects scratch. If there is any damage, please use the repair kit to repair in time to avoid complete damage

Products from this seller

See more